switch

(PHP 4, PHP 5, PHP 7, PHP 8)

The switch statement is similar to a series of IF statements on the same expression. In many occasions, you may want to compare the same variable (or expression) with many different values, and execute a different piece of code depending on which value it equals to. This is exactly what the switch statement is for.

Note: Note that unlike some other languages, the continue statement applies to switch and acts similar to break. If you have a switch inside a loop and wish to continue to the next iteration of the outer loop, use continue 2.

Note:

Note that switch/case does loose comparison.

In the following example, each code block is equivalent. One uses a series of if and elseif statements, and the other a switch statement. In each case, the output is the same.

Example #1 switch structure

<?php
// This switch statement:

switch ($i) {
    case 
0:
        echo 
"i equals 0";
        break;
    case 
1:
        echo 
"i equals 1";
        break;
    case 
2:
        echo 
"i equals 2";
        break;
}

// Is equivalent to:

if ($i == 0) {
    echo 
"i equals 0";
} elseif (
$i == 1) {
    echo 
"i equals 1";
} elseif (
$i == 2) {
    echo 
"i equals 2";
}
?>

It is important to understand how the switch statement is executed in order to avoid mistakes. The switch statement executes line by line (actually, statement by statement). In the beginning, no code is executed. Only when a case statement is found whose expression evaluates to a value that matches the value of the switch expression does PHP begin to execute the statements. PHP continues to execute the statements until the end of the switch block, or the first time it sees a break statement. If you don't write a break statement at the end of a case's statement list, PHP will go on executing the statements of the following case. For example:

<?php
switch ($i) {
    case 
0:
        echo 
"i equals 0";
    case 
1:
        echo 
"i equals 1";
    case 
2:
        echo 
"i equals 2";
}
?>

Here, if $i is equal to 0, PHP would execute all of the echo statements! If $i is equal to 1, PHP would execute the last two echo statements. You would get the expected behavior ('i equals 2' would be displayed) only if $i is equal to 2. Thus, it is important not to forget break statements (even though you may want to avoid supplying them on purpose under certain circumstances).

In a switch statement, the condition is evaluated only once and the result is compared to each case statement. In an elseif statement, the condition is evaluated again. If your condition is more complicated than a simple compare and/or is in a tight loop, a switch may be faster.

The statement list for a case can also be empty, which simply passes control into the statement list for the next case.

<?php
switch ($i) {
    case 
0:
    case 
1:
    case 
2:
        echo 
"i is less than 3 but not negative";
        break;
    case 
3:
        echo 
"i is 3";
}
?>

A special case is the default case. This case matches anything that wasn't matched by the other cases. For example:

<?php
switch ($i) {
    case 
0:
        echo 
"i equals 0";
        break;
    case 
1:
        echo 
"i equals 1";
        break;
    case 
2:
        echo 
"i equals 2";
        break;
    default:
       echo 
"i is not equal to 0, 1 or 2";
}
?>

Note: Multiple default cases will raise a E_COMPILE_ERROR error.

Note: Technically the default case may be listed in any order. It will only be used if no other case matches. However, by convention it is best to place it at the end as the last branch.

If no case branch matches, and there is no default branch, then no code will be executed, just as if no if statement was true.

A case value may be given as an expression. However, that expression will be evaluated on its own and then loosely compared with the switch value. That means it cannot be used for complex evaluations of the switch value. For example:

<?php
$target 
1;
$start 3;

switch (
$target) {
    case 
$start 1:
        print 
"A";
        break;
    case 
$start 2:
        print 
"B";
        break;
    case 
$start 3:
        print 
"C";
        break;
    case 
$start 4:
        print 
"D";
        break;
}

// Prints "B"
?>

For more complex comparisons, the value true may be used as the switch value. Or, alternatively, if-else blocks instead of switch.

<?php
$offset 
1;
$start 3;

switch (
true) {
    case 
$start $offset === 1:
        print 
"A";
        break;
    case 
$start $offset === 2:
        print 
"B";
        break;
    case 
$start $offset === 3:
        print 
"C";
        break;
    case 
$start $offset === 4:
        print 
"D";
        break;
}

// Prints "B"
?>

The alternative syntax for control structures is supported with switches. For more information, see Alternative syntax for control structures.

<?php
switch ($i):
    case 
0:
        echo 
"i equals 0";
        break;
    case 
1:
        echo 
"i equals 1";
        break;
    case 
2:
        echo 
"i equals 2";
        break;
    default:
        echo 
"i is not equal to 0, 1 or 2";
endswitch;
?>

It's possible to use a semicolon instead of a colon after a case like:

<?php
switch($beer)
{
    case 
'tuborg';
    case 
'carlsberg';
    case 
'stella';
    case 
'heineken';
        echo 
'Good choice';
        break;
    default;
        echo 
'Please make a new selection...';
        break;
}
?>

See Also

Here you can write a comment


Please enter at least 10 characters.
Loading... Please wait.
* Pflichtangabe
There are no comments available yet.

PHP cURL Tutorial: Using cURL to Make HTTP Requests

cURL is a powerful PHP extension that allows you to communicate with different servers using various protocols, including HTTP, HTTPS, FTP, and more. ...

TheMax

Autor : TheMax
Category: PHP-Tutorials

Midjourney Tutorial - Instructions for beginners

There is an informative video about Midjourney, the tool for creating digital images using artificial intelligence, entitled "Midjourney tutorial in German - instructions for beginners" ...

Mike94

Autor : Mike94
Category: KI Tutorials

Basics of views in MySQL

Views in a MySQL database offer the option of creating a virtual table based on the result of an SQL query. This virtual table can be queried like a normal table without changing the underlying data. ...

admin

Autor : admin
Category: mySQL-Tutorials

Publish a tutorial

Share your knowledge with other developers worldwide

Share your knowledge with other developers worldwide

You are a professional in your field and want to share your knowledge, then sign up now and share it with our PHP community

learn more

Publish a tutorial